Skip to main content
 首页 » 编程设计

python之将值从一个 python 脚本发送到另一个 python 脚本

2025年04月02日9mate10pro

所以我有一些值通过 RF 收发器 (NRF24L01) 从 Arduino 传到我的 Raspberry Pi,我可以在程序运行时显示整数 (Python)。现在我想在我用单独的 python 脚本编写的 GUI 中显示那些整数值。我很难这样做。我试过从 GUI 导入它们,但它不起作用,我不知道为什么..

所以现在我已经选择了将值写入传输脚本中的文本文件,然后尝试从 GUI 脚本中的文本文件中读取值,但它仍然无法正常工作。

谁能帮我更新传输脚本中的文本文件并从 GUI 脚本中读取它?能否同时从一个脚本写入文本文件并从另一个脚本读取文本文件?

任何帮助将不胜感激。谢谢!

附言。如果我遗漏了任何您需要知道的信息,请直接提问。解释一切有点困难!

GUI 代码

# -*- coding: utf-8 -*- 
""" 
Created on Sat Aug  6 20:05:30 2016 
 
@author: s 
""" 
import sys 
 
if sys.version_info[0] < 3: 
    import Tkinter as tk 
else: 
    import tkinter as tk 
 
 
def clear(): 
    pass 
 
 
def exit_(): 
    root.quit() 
    root.withdraw() 
 
 
#water_amount = 0 
water_cost = 0 
total_water_amount = 0 
total_water_cost = 0 
 
 
 
def show_data(): 
    while True: 
        text_file = open("Output.txt", "r") 
        water_amount = text_file.readlines() 
        text_file.close() 
 
        tk.Label(root, text='Water Amount: ' + str(water_amount)).pack() 
        tk.Label(root, text='Water Cost: ' + str(water_cost)).pack() 
 
        separator = tk.Frame(height=2, bd=10, relief=tk.SUNKEN) 
        separator.pack(fill=tk.X, padx=5, pady=5) 
 
        tk.Label(root, text='Total Water Amount: ' + str(total_water_amount)).pack() 
        tk.Label(root, text='Total Water Cost: ' + str(total_water_cost)).pack() 
 
        separator = tk.Frame(height=2, bd=10, relief=tk.SUNKEN) 
        separator.pack(fill=tk.X, padx=5, pady=5) 
 
#show_data() 
 
 
def get_rate(): 
    import random 
    for i in range(100): 
        flow_rate.append(random.randint(20, 60)) 
        # print(flow_rate) 
 
 
# def draw_plot(flow_rate): 
#     import matplotlib.pyplot as plt 
#     conda install matplotlib 
#     print(flow_rate) 
#     plt.plot(flow_rate, label='Flow rate ml/sec') 
#     plt.xlabel('Time(sec)') 
#     plt.ylabel('Flow Rate(ml)') 
#     plt.title("Flow Rate Chart") 
# 
#     plt.legend() 
#     plt.show() 
 
 
root = tk.Tk(className='Water') 
flow_rate = [] 
get_rate() 
show_data() 
tk.Button(root, text='Clear', command=clear).pack(side='left') 
tk.Button(root, text='Exit', command=exit_).pack(side='left') 
#tk.Button(root, text='Draw', command=draw_plot(flow_rate)).pack_forget() 
 
 
 
root.mainloop() 

代码接收值

import RPi.GPIO as GPIO 
from lib_nrf24 import NRF24 
import time 
import spidev 
 
GPIO.setmode(GPIO.BCM) 
 
pipes = [[0xE8, 0xE8, 0xF0, 0xF0, 0xE1], [0xF0, 0xF0, 0xF0, 0xF0, 0xE1]] 
 
radio = NRF24(GPIO, spidev.SpiDev()) 
radio.begin(0,17) 
 
radio.setPayloadSize(32) #can have maximum 32 
radio.setChannel(0x76) 
radio.setDataRate(NRF24.BR_1MBPS) #Slower since it is secure 
radio.setPALevel(NRF24.PA_MIN) # Minimum to save battery 
 
radio.setAutoAck(True) 
radio.enableDynamicPayloads() 
radio.enableAckPayload() #Acknowledgement Payload : Can verify if data received 
 
radio.openReadingPipe(1, pipes[1]) 
radio.printDetails() 
radio.startListening() 
 
while True: 
 
    # Waits to recieve data, if no data is recieved then goes into sleep mode 
    while not radio.available(0): 
        time.sleep(1/100) 
 
 
    receivedMessage = [] 
    #Populates the message 
    radio.read(receivedMessage, radio.getDynamicPayloadSize()) 
 
    #------------------------------------------------------- 
    raw = int(receivedMessage[1]) * 256 
    total = raw + int(receivedMessage[0]) 
    print ("total equals:" + str(int(total))) 
    text_file = open("Output.txt", "w") 
    text_file.write("%s" % total) 
    text_file.close() 

请您参考如下方法:

你应该尝试将数据接收代码和数据显示代码与threading库结合起来。

在数据接收脚本的 while True 循环中,它应该检查新结果并以某种方式通知 GUI 线程(例如,将其存储在全局变量中并使用 threading .Condition 对象),或者直接更改 GUI。

例如:

from tkinter import * 
import threading 
 
tk=Tk() 
result=StringVar() 
 
Label(tk,textvariable=result).pack() 
 
def update_result(): 
    import RPi.GPIO as GPIO 
    from lib_nrf24 import NRF24 
    import time 
    import spidev 
 
    GPIO.setmode(GPIO.BCM) 
 
    pipes = [[0xE8, 0xE8, 0xF0, 0xF0, 0xE1], [0xF0, 0xF0, 0xF0, 0xF0, 0xE1]] 
 
    radio = NRF24(GPIO, spidev.SpiDev()) 
    radio.begin(0,17) 
 
    radio.setPayloadSize(32) #can have maximum 32 
    radio.setChannel(0x76) 
    radio.setDataRate(NRF24.BR_1MBPS) #Slower since it is secure 
    radio.setPALevel(NRF24.PA_MIN) # Minimum to save battery 
 
    radio.setAutoAck(True) 
    radio.enableDynamicPayloads() 
    radio.enableAckPayload() #Acknowledgement Payload : Can verify if data received 
 
    radio.openReadingPipe(1, pipes[1]) 
    radio.printDetails() 
    radio.startListening() 
 
    while True: 
        while not radio.available(0): 
        time.sleep(1/100) 
 
        receivedMessage = [] 
        #Populates the message 
        radio.read(receivedMessage, radio.getDynamicPayloadSize()) 
 
        #------------------------------------------------------- 
        raw = int(receivedMessage[1]) * 256 
        total = raw + int(receivedMessage[0]) 
        result.set(total) 
 
 
threading.Thread(target=update_result).start() 
mainloop() 

(我没有测试这个程序,因为我没有环境,但我认为应该可以,如果不行请评论。)